调节指导-智能装盒机80DAdjustment Instruction - Intelligent Cartridge 80D
发布时间：
2024-10-19 09:36
智能装盒机80D
1、开机指导Start-up Guidance
2、纸盒与链条间距离调节指导Guide for adjusting the distance between carton and chain
3、纸盒库大小规格切换指导
4、纸盒成型状态与机器的位置Carton forming status and machine position
5、调整推杆与纸盒间的位置Adjust the position between the push rod and the carton
6、调整产品与机器存放产品的物料斗位置Adjust the position of the product and the material hopper where the machine stores the product
7、纸盒封口问题分析Analysis of carton sealing problem
操作安全提示
Operation safety tips
a．在操作运行时，必须遵守技术安保的基本条例：
During operation must obey the basic regulations of the technical safety assurance instructions.
b．机器控制箱应当可靠的接地。
The machine control cabinet must be faithfully earthed.
c．工作时禁止任何机构调整。
Forbid to adjust any device during operation.
d．运转时人的任何部位不能伸到主机机构的运行半径内。
All parts of human body are not allowed to be within the radius range of the main machine during operation.
e．非专业人员请不要打开电箱。
Non professional personnel shall not open the electricity box.
2. 保养. 润滑
a. 每天上下班对机器搞好卫生，检查连接螺钉是否松动。
Clean up the machine at the beginning and end of every working day and check whether the connection bolt is loose or not.
b.经常观察机器是否运转正常，是否有异响、异味。
Always observe whether the machine is operating normally or not and whether there is abnormal noise or particular smell.
c．各种关节轴承每周注入1-2滴润滑液。链轮和凸轮每半个月适量注入润滑油一次。
Inject 1-2 drops of lubricant into all kinds of joint bearing every week. Chain wheel and cam wheel shall be lubricated with proper grease once half a month.
d. 每个月对控制系统清理、保养一次。
Clean and maintain once a month for the control system.
机器的保养和维护
Machine care and maintenance
1. 机器要保持清洁，经常进行擦拭、润滑转动零件。The machine should be kept clean, wipe and lubricate the rotating parts frequently
2. 凸轮机构、传动链 部件应每隔15～40个工作小时 润滑一次。建议使用牌号为50的机械油（运动粘度47～53mm²/S50℃）对于齿轮啮合处应每三个月添加一次润滑脂，建议使用钙基润滑脂，牌号为ZG-1或ZG-2。2. The cam mechanism and transmission chain components should be lubricated every 15-40 working hours. It is recommended to use a mechanical oil grade of 50 (kinematic viscosity 47～53mm²/S50℃). Grease should be added every three months to the gear mesh. It is recommended to use calcium-based grease, grade ZG-1 or ZG-2.
3. 同步齿形带及传动胶带应避免与油接触，以免降低其使用寿命。Synchronous toothed belts and transmission belts should avoid contact with oil, so as not to reduce their service life
4. 保证机器能正常可靠地工作，应每隔三个月停机一次，检查传动链的张紧情况和传动零部件的紧固程度，必要时重新调节和紧固。To ensure that the machine can work normally and reliably, it should be shut down every three months to check the tension of the transmission chain and the tightness of the transmission components, and re-adjust and tighten if necessary.
5. 出现故障后应仔细分析，并由有关机修人员维修排除，禁止乱调拆，以免损坏零件。After the failure occurs, it should be carefully analyzed, and repaired and eliminated by the relevant mechanics. It is forbidden to adjust and disassemble, so as to avoid damage to the parts.
回复帮忙寻找帮忙
回复咨询咨询设备
回复招聘等你过来
最新资讯
